siliXon

Through-hole boards you can solder yourself

You can now set your boards to use through-hole components by selecting the Do It Yourself option.

siliXon turns a plain-English description of a device into a printed circuit board design. Until this month, Rocky designed boards for a factory to assemble, usually with tiny surface-mount parts and a bare microcontroller chip. Those are hard to solder at home.

Now Rocky asks how you want your board built. Pick Do It Yourself and you get a board you can put together at your desk with a basic soldering iron. It uses parts with legs and a ready-made dev board, such as an Arduino or a Raspberry Pi Pico.

You asked for it

We built this because you kept asking for it. From late August until we finished it in early November, at least 60 different people asked Rocky for through-hole parts or for a board they could solder by hand. Here are a few of those requests, reworded to keep them anonymous:

  • A student who wanted to order bare boards and solder the parts themselves, instead of paying for factory assembly.
  • Someone with a stash of spare through-hole resistors who wanted a project that used them up.
  • A hobbyist who said the leadless chip Rocky had picked was impossible to solder without a hot-air gun, and asked for DIP chips or parts with big legs instead.
  • Several people who asked Rocky to swap every surface-mount part for a through-hole one.
  • Someone who simply asked for a board they could solder at home, instead of having a factory build it.

Rocky did its best with those requests, but it was still designing for a factory. It could swap in a through-hole resistor when asked. The microcontroller, though, was usually still a surface-mount chip, and so were the USB socket, buttons and power parts around it.

How we counted: we searched the requests people sent Rocky on the live app from 1 June to 5 November for phrases like "through-hole" and "hand-solder", read every match, and kept only people asking for through-hole parts or a board they could solder themselves. We left out siliXon's own team. Requests worded differently, or in other languages, aren't counted, so 60 is a lower bound.

What Do It Yourself changes

On a Do It Yourself board, Rocky:

  • Picks parts with legs. Resistors, capacitors, LEDs, buttons and chips whose legs go through holes in the board. When no through-hole part does the job, Rocky uses a surface-mount part with leads an iron can reach (such as SOIC or SOT-23) and tells you. It doesn't use leadless packages (QFN, LGA or BGA).
  • Puts a ready-made dev board in charge. Instead of a bare microcontroller chip, the board carries a small dev board, such as an Arduino Nano or a Raspberry Pi Pico. Tell Rocky which one you have, or let it pick one that fits: for example, one with Wi-Fi or Bluetooth if your project needs a radio. If siliXon doesn't carry yours, Rocky says so and offers the closest match.
  • Runs it from the dev board's USB cable. The same cable powers the board and loads your code, so Rocky leaves out the USB socket, the BOOT and RESET buttons and the power parts a bare chip would need. If you want batteries or another power source, just ask. Big loads, such as motors or long LED strips, need a supply of their own, and Rocky tells you when that's the case.
  • Uses standard connectors. Wires that leave the board go to 2.54 mm pin headers or screw terminals.
  • Keeps ordering simple. You download the manufacturing files, order bare boards from any PCB maker and buy the parts on the parts list.

The plant-watering reminder from the film: a Raspberry Pi Pico W on pin headers, a red LED, two push buttons and resistors with legs.

Easier to get working

Do It Yourself is designed to give your board a better chance of working first time, and to make problems easier to fix:

  • The hardest part comes ready-made. The dev board arrives with the microcontroller, USB port, power circuit and clock already on it. You program it over USB, just as you would on a breadboard.
  • The joints are big enough to check. Through-hole joints are easy to inspect by eye, and a bad one can usually be touched up with the same iron that made it.
  • The parts are the ones you find in starter kits. Through-hole resistors, LEDs and buttons fit a breadboard, so you can try the circuit before you solder anything.

Cheaper to build

  • No assembly fees. You pay for bare boards and parts, and nothing for assembly. On 17 November 2026, JLCPCB listed five bare boards from $2. Their Economic assembly service adds an $8.18 setup fee, $1.53 for the stencil and a $3.07 feeder fee for each type of Extended part (parts they don't keep loaded on their machines), on top of the cost of the parts.
  • A dev board can cost just a few dollars. Raspberry Pi lists the Pico from $4 and the Pico W at $6.
  • A basic iron is enough. You don't need a hot-air station, a reflow oven or a solder paste stencil.
  • Mistakes cost less. You can usually fix a bad joint or a wrong resistor at your desk (a desoldering pump or wick helps) instead of paying for another assembled order. Bare boards also come in batches (JLCPCB's quote starts at five), so one ruined board isn't the end of the project.
  • You can use what you have. Through-hole resistors, LEDs and buttons are sold almost everywhere, and many people already have a drawer full of them.

Do It Yourself is meant for one-off and small builds. If you plan to make many copies, Rocky recommends the factory instead.

How Rocky helps you choose

If your request doesn't say how the board will be built, Rocky asks before doing anything else. It shows both options with a picture of each, recommends one and gives its reason in a sentence. The choice is yours. If you reply without picking, Rocky goes with Manufactured in Factory and tells you.

Rocky's card after the request for a plant-watering reminder, with Do It Yourself picked.

Some requests answer the question already. If you ask for factory assembly, Rocky builds the board Manufactured in Factory. It does the same if you list your exact parts and none of them is a dev board, then offers Do It Yourself once that build is done.

Rocky recommends Do It Yourself when three things are true: a dev board can run the project, every other part is available with legs or as a plug-in module (LEDs, buttons, knobs, buzzers, relays, small displays and sensor modules), and you haven't asked for a small or wearable board or for several copies. Most one-off, hobby, desk and learning builds fit: a reaction game, a desk clock, a plant waterer, a weather logger.

Rocky recommends Manufactured in Factory for everything else: wearables, trackers, boards that have to fit a case and products made in volume. The same goes for designs that need a chip or connector that only comes in a surface-mount package, or delicate wiring such as USB data, fast signals, or a radio or audio circuit of their own. Wi-Fi or Bluetooth built into the dev board is fine for Do It Yourself.

If your request says "I'll solder it myself" or "through-hole", or is built around a dev board, Rocky still shows the card, with Do It Yourself recommended. The board is only set once you click.

If you'd rather solder the tiny parts of a factory board yourself, you don't need Do It Yourself. Pick Manufactured in Factory and order bare boards. That takes more skill, though: small parts need a fine-tip iron and practice, and some chips need hot air or a reflow oven.

Good to know

  • The board is bigger. Parts with legs take up more room than surface-mount ones.
  • You choose per board. Switching a board later means replacing nearly every part, so Rocky asks first.
  • Some chips only come in tiny packages. If your design needs a chip that only comes in a leadless package, Rocky tells you and offers to switch the board to Manufactured in Factory.
  • Check before you order. As with any board, review it in the editor and run siliXon's manufacturing checks before you order.

Do It Yourself has been available to every siliXon user since 9 November, when it launched as Easy solder. On 16 November it got its new name, the pictures and Rocky's recommendation.

Try it

Open app.silixon.io, describe what you want to build, and pick Do It Yourself when Rocky asks. A request can be as simple as this:

A reaction game with two buttons, four LEDs and a buzzer. I'll solder it myself.